MEL aluminum Valley cover project proposal

Exchange knowledge and discuss MEL engine related aftermarket engine parts like cams, rods, chains, intakes and lots more.
User avatar
buddy67lincoln
Senior Airman
Senior Airman
Posts: 129
Joined: Tue 23. Dec 2008, 09:28
Gender: male
Music instruments you're playing: The Kazoo
Location: Pittsburgh, PA
Contact:

Re: MEL aluminum Valley cover project proposal

Post by buddy67lincoln » Tue 8. Dec 2009, 11:01

What ever happened to these??? Were they made or not...if so I WANNA SEE SOME PHOTOS! I'd like one too but it seems it never happened. Thanks
John Lyman
1964 Continental Convertible (actually working on this one!)
1967 Continental Coupe (bucket of rust)
1966 Continental Coupe (mild custom some day???)
1967 Continental 4 door (30,000 miles, part car)
1967 Continental 4 door (scrapped)

Chris Craft crazy
Technical Sergeant
Technical Sergeant
Posts: 238
Joined: Fri 4. Sep 2009, 06:53
Gender: male
Music instruments you're playing: Guitar
Location: Ontario Canada

Re: MEL aluminum Valley cover project proposal

Post by Chris Craft crazy » Sun 13. Dec 2009, 16:45

I think it still has life, and I am still interested.....
MEL Marine division... and if you thought MEL car parts were scarce....

56vicky430
Airman basic
Posts: 13
Joined: Tue 3. Feb 2009, 11:57
Gender: male
Music instruments you're playing: none

Re: MEL aluminum Valley cover project proposal

Post by 56vicky430 » Mon 14. Dec 2009, 15:54

buddy67lincoln wrote:What ever happened to these??? Were they made or not...if so I WANNA SEE SOME PHOTOS! I'd like one too but it seems it never happened. Thanks


It's is "happening" I didn't get the stock covers sent until early this month. Everybody just hang tight.

Rocky

Chris Craft crazy
Technical Sergeant
Technical Sergeant
Posts: 238
Joined: Fri 4. Sep 2009, 06:53
Gender: male
Music instruments you're playing: Guitar
Location: Ontario Canada

Re: MEL aluminum Valley cover project proposal

Post by Chris Craft crazy » Wed 16. Dec 2009, 01:32

Nobody I can think of would be mad if it was a little more than originally quoted to cover your time... ;)
MEL Marine division... and if you thought MEL car parts were scarce....

User avatar
Theo
Administrator
Administrator
Posts: 1209
Joined: Sun 21. Dec 2008, 14:10
Gender: male
Location: Berlin / Potsdam in Germany
Contact:

Re: MEL aluminum Valley cover project proposal

Post by Theo » Wed 16. Dec 2009, 03:36

Please allow me to write down a few thoughts that come up each time I read about alum. valley pans.
They sure look fancy, but they're probably tricky in combat.
Unless you are working on a perfectly blueprinted engine block with all geometries ideal, installation will need your close extra attention. In most instances irregularities at the block's mating surfaces, such as not being perfectly parallel or situations were you have stepped surfaces between block and cylinder heads etc. the good old flexible steel stamped pan did fine. It's flexible enough to compensate in those areas and at stress points such as the bolt holes areas .
With an aluminum pan I'm not sure if the gasket thickness is gonna compensate enough. In the worst case you'll probably take chances to crack your investment.
I've been working on blocks that were not "block trued" and I can tell you, it was a mess. Especially when the intake manifold didn't mate those twisted surfaces.
I don't mean to spoil the thread and your drooling in aluminum heaven. That thing will sure look great on your engine. Just a few thoughts in a discussion board to throw in.
BTW will the v-pan be finned?
Best regards
Theo
Admin

Chris Craft crazy
Technical Sergeant
Technical Sergeant
Posts: 238
Joined: Fri 4. Sep 2009, 06:53
Gender: male
Music instruments you're playing: Guitar
Location: Ontario Canada

Re: MEL aluminum Valley cover project proposal

Post by Chris Craft crazy » Wed 16. Dec 2009, 16:33

Yep, I agree that could be a problem, although working out a thicker custom gasket might help.
MEL Marine division... and if you thought MEL car parts were scarce....

User avatar
Theo
Administrator
Administrator
Posts: 1209
Joined: Sun 21. Dec 2008, 14:10
Gender: male
Location: Berlin / Potsdam in Germany
Contact:

Re: MEL aluminum Valley cover project proposal

Post by Theo » Wed 16. Dec 2009, 17:43

I think the aluminum valley pan should be of a thick and sturdy construction. It should have extra meat at stress points and at the gasket surfaces in general. On a trued block those aluminum pans can be superior to the steel pans, but if the blocks are not true, they will be problematic to install
valley_pan_thoughts.jpg
valley_pan_thoughts2.jpg
Best regards
Theo
Admin

Chris Craft crazy
Technical Sergeant
Technical Sergeant
Posts: 238
Joined: Fri 4. Sep 2009, 06:53
Gender: male
Music instruments you're playing: Guitar
Location: Ontario Canada

Re: MEL aluminum Valley cover project proposal

Post by Chris Craft crazy » Tue 9. Feb 2010, 12:59

Any further word on valley covers?
MEL Marine division... and if you thought MEL car parts were scarce....

User avatar
buddy67lincoln
Senior Airman
Senior Airman
Posts: 129
Joined: Tue 23. Dec 2008, 09:28
Gender: male
Music instruments you're playing: The Kazoo
Location: Pittsburgh, PA
Contact:

Re: MEL aluminum Valley cover project proposal

Post by buddy67lincoln » Tue 9. Feb 2010, 13:41

The engineering is a concern so maybe that's what is going on right now...just making sure to cover all 'worst case scenarios' I'd sure love one or 2 of those if it all works out. These finned valley covers would look great with those finned rocker covers Moon made. Will the fins be spaced approx the same and have the same thickness (the fins that is)? We can measure when they come in or just compare to any other Moon valve cover. Thanks and looking forward to an update!
John Lyman
1964 Continental Convertible (actually working on this one!)
1967 Continental Coupe (bucket of rust)
1966 Continental Coupe (mild custom some day???)
1967 Continental 4 door (30,000 miles, part car)
1967 Continental 4 door (scrapped)

56vicky430
Airman basic
Posts: 13
Joined: Tue 3. Feb 2009, 11:57
Gender: male
Music instruments you're playing: none

Re: MEL aluminum Valley cover project proposal

Post by 56vicky430 » Fri 9. Apr 2010, 16:09

The design is being tweaked right now. I received one and there was going to be some bolt alignment problems on the side. Those are going to be elongated front to back to allow for shifting on different head profiles. There is going to be some work in the front and back saddles that guys are just going to have to work out on their own. It's going to be hard to have a perfectly fitting cover for everyone. I have the moon covers and the thin thickness and height of the fins was right for a matched look. I sent that back a few weeks ago. He's working on other stuff too right now. I'll keep everyone posted.


Rocky

Post Reply

Return to “MEL Engine Aftermarket Parts”

Who is online

Users browsing this forum: No registered users and 1 guest