Page 2 of 3

Early 1958 430 rebuild

Posted: Fri 16. Mar 2018, 14:22
by RocketdyneF1
After searching for a good camshaft for a long time, i´ve finally found a good one!
The cam is Falcon Performance #CM-184, a new reproduction of a stock cam, at least they say so. I couldn´t measure its duration, but i measured the valve lift at about 0.440", so its probably a reproduction of the early style stock cam i was looking for.
DSCN2484.jpg
After I installed the new cam, valve lifters and timing chain, I disassembled both rocker shafts. I guess they´ve never been serviced and the dirty, muddy scab on them was 60 years old.
DSCN2502.JPG
I cleaned and inspected them, wich was a good thing, because some oil passages were almost full of crap. I also cleaned all 16 pushrods.
DSCN2507.JPG
DSCN2510.JPG
I also cleaned and painted the oil pan and refurbished the oil pump with a rebuild kit.
DSCN2500.JPG
DSCN2503.JPG
The valve train and oiling system are complete again.
DSCN2515.JPG
DSCN2513.JPG
DSCN2511.JPG

Early 1958 430 rebuild

Posted: Fri 23. Mar 2018, 14:02
by RocketdyneF1
Today I assembled the valley pan, ignition distributor, timing chain cover with fuel pump pushrod, flywheel, valve covers and the Tri Power system. Finally it looks like an engine!
DSCN2525.JPG
DSCN2529.JPG
DSCN2530.JPG
DSCN2533.JPG
DSCN2534.JPG
DSCN2535.JPG
DSCN2536.JPG
DSCN2537.JPG

Early 1958 430 rebuild

Posted: Sat 24. Mar 2018, 15:08
by RocketdyneF1
A few more pics of the progress:
DSCN2542.JPG
DSCN2544.JPG
DSCN2545.JPG
DSCN2547.JPG
DSCN2551.JPG
DSCN2553.JPG
DSCN2557.JPG
DSCN2558.JPG
I hope I can start it up soon!

Re: Early 1958 430 rebuild

Posted: Sun 25. Mar 2018, 21:22
by Chris430
Are there provisions in a 58 Ford to bolt up your early 58 block without the side mount bosses?

Re: Early 1958 430 rebuild

Posted: Mon 26. Mar 2018, 05:09
by RocketdyneF1
Chris430 wrote:
Sun 25. Mar 2018, 21:22
Are there provisions in a 58 Ford to bolt up your early 58 block without the side mount bosses?
Sorry, I dont know that. But a beautiful 58 Ford with this big engine sounds good to me!
Too bad I dont have one. Actually I dont have any car for my MEL engine. When I bought the engine, I planned to by a car for it, but I ran out of money. So I´ll store the engine when its completely rebuildt. Or maybe, if I get a good offer, I might even sell it.

Early 1958 430 rebuild

Posted: Thu 17. May 2018, 05:34
by RocketdyneF1
Today, I finally started up the engine for the first time in years. It only ran for a few seconds, but damn, it has a really loud and brutal sound! No wonder, it has absolutley no exhaust system on it except for the manifolds. I also havent bought a radiator and cooling fan for it yet, so I cant let it run for longer periods of time. I´ll post a video of it running when I am done tuning the carbs and ignition, and the cooling system is complete.
DSCN2570.JPG
DSCN2571.JPG
DSCN2575.JPG
DSCN2572.JPG
DSCN2573.JPG

Re: Early 1958 430 rebuild

Posted: Thu 17. May 2018, 06:40
by Theo
WoW!! Very nice (Y)

Re: Early 1958 430 rebuild

Posted: Sat 19. May 2018, 08:08
by Chris430
[youtube2]
[/youtube2]

You should let me store it in my pick-up till you find a suitable car.

Re: Early 1958 430 rebuild

Posted: Sat 19. May 2018, 13:15
by Theo
Holy cow. That I call music

Early 1958 430 rebuild

Posted: Sat 21. Jul 2018, 10:30
by RocketdyneF1
I finally made a video of it running.



enjoy!